花岗岩的黑火药爆炸切割技术

本文介绍了爆炸切割与光面爆破的区别；系统阐述了石材切割技术方案选择、黑火药爆炸切割参数的确定、切割工艺、起爆技术及切割实例。     

磨矿方式对方解石颗粒形貌及浮选行为的影响

磨矿是浮选分离成功的前提。通过磨矿试验、单矿物浮选试验、润湿性测试、扫描电镜测试，研究了陶瓷棒磨与陶瓷球磨，不同磨矿方式对方解石颗粒表面形貌及浮选行为的影响。试验结果表明，经过陶瓷球磨处理后的方解石矿物颗粒相较于经过陶瓷棒磨处理后的方解石矿物颗粒有着更大的疏水性，更好的浮选回收率，更大的扁平率与伸长率，以及更小的圆度和相对宽度。      

臭氧氧化-循环喷淋法处理钨钼选矿废水

采用臭氧氧化-循环喷淋法去除钨钼选矿废水中COD,研究了pH值、臭氧流量、循环频率对COD去除效果的影响。结果表明: 废水COD去除率随pH值、臭氧流量、循环频率增大而增加,在pH值为10、臭氧流量3.0 L/min、循环频率4.0次/min条件下,氧化120 min后废水COD含量由131 mg/L降至11.5 mg/L,COD去除率达91.2%,满足《污水综合排放标准》(GB 8978-1996)一级标准。与O₂、NaClO处理废水COD的对比试验结果表明,循环喷淋法结合O₃表现出较好的COD去除效果。     

Improving room-temperature electrochemical performance of solid-state lithium battery by using electrospun La2Zr2O7 fibers-filled composite solid electrolyte

Low ionic conductivity at room temperature and poor interfacial compatibility are the main obstacles to restrain the practical application of polymer solid electrolytes. In this work, lanthanum zirconate (LZO) fibers were prepared by electrospinning method and used for the first time as fillers in sandwich polypropylene carbonate (PPC)-based solid electrolyte. Meanwhile, a graphite coating was applied on one surface of the composite solid electrolyte (CSE) membrane. The results show that the LZO fibers significantly increases the room-temperature electrochemical performance of the CSE, and the graphite coating enhances the interfacial compatibility between electrolyte and lithium anode. Furthermore, an ultra-thin PPC-LZO CSE with a total thickness of 22 μm was prepared and used in NCM622/CSE/Li solid-state cell, which shows an initial discharge capacity of 165.6 mAh/g at the current density of 0.5C and a remaining capacity of 113.0 mAh/g after 250 cycles at room temperature. Rise to 1C, the cell shows an initial discharge capacity of 154.2 mAh/g with a remaining capacity of 95.6 mAh/g after 250 cycles. This ultra-thin CSE is expected to be widely applied in high energy-density solid-state battery with excellent room-temperature electrochemical performances.     

现代审美视角下非遗文创品牌的视觉设计及包装插画研究

文章从现代审美视角出发,结合前人的研究论证,探讨与补充非遗文创在品牌视觉设计及包装插画方面研究的理论不足,为设计者提供更加开阔的设计思路和更为新颖的设计手法,从而提升非遗文创的整体设计效果。     

印度洋海盆沉积物中稀土的赋存状态及其浸出研究

印度洋海盆沉积物作为重要的稀土资源，已成为保障我国稀土供应的重要途径。为探究利用印度洋海盆沉积物提取稀土的可行性，通过激光粒度分析、化学物相分析、SEM分析等考察了某印度洋海盆沉积 物中稀土元素赋存状态，并采用硫酸为浸出剂，研究硫酸浓度、液固比、浸出温度及时间对稀土浸出率的影响，对最佳条件下获得的浸出液通过氨水中和沉淀净化。结果表明：①沉积物颗粒极细，体积平均粒径仅 4.47 μm，其主要矿物组成为黏土、锰氧化物、石英、长石、云母、绿泥石和石盐，其中稀土主要赋存于磷灰石中，占总稀土比例达73.10%；②在硫酸浓度2 mol/L，液固比7∶1，浸出温度55 ℃，浸出时间120 min的 最佳条件下，主要稀土元素La、Ce、Nd和Y的浸出率分别为80.57%，66.33%，88.42%和93.25%，高价值的重稀土Gd、Dy和Er浸出率分别为92.63%、55.30%和93.17%。③稀土浸出液成分复杂，且稀土含量偏低，仅有100 mg/L左右，采用氨水调节pH值至5.14，可有效去除Al和Fe，但稀土损失率也达到了30.85%。该研究结果对进一步开发利用深海稀土资源具有重要意义。     

潮流能水平轴水轮机在剪切来流下的水动力分析

采用基于计算流体力学方法的全尺度数值模拟计算,建立了适用于潮流能水轮机模拟的剪切来流环境,通过数值计算结果,对潮流能水轮机随时间变化的宏观力和流场特征进行了系统分析,探索水轮机在复杂工况下的水动力特性规律。结果表明,水轮机整个叶轮的总体平均受力在剪切流工况中未受到明显影响; 单个叶片的瞬态轴向力系数和瞬态轴向扭矩系数在旋转周期内出现了明显的周期性变化,且周期性变化幅值随转速增大而增大; 非定常的瞬时轴向扭矩和力的周期性振荡容易引起单个叶片的结构性振动,可能对水轮机的机械结构造成影响。     

Fe3+与水玻璃组合抑制剂对萤石和方解石浮选分离的影响

萤石和方解石表面都存在Ca2+的活性位点且两种矿物表面性质相近，导致萤石和方解石的分离难度较大。通过单矿物浮选试验、吸附量测定、Zeta电位测量以及浮选溶液化学计算，并引入Fe3+，将其与水玻璃混合，研究该组合抑制剂对萤石和方解石浮选分离的影响及其机理。浮选试验结果表明，与水玻璃相比，Fe-水玻璃选择性抑制了方解石的浮选，实现了两种矿物的分离。机理测试结果表明，Fe3+与水玻璃在溶液中反应的产物Fe-水玻璃聚合物以及水玻璃的水解组分Si（OH）₄在方解石表面发生较强的吸附作用，阻碍了油酸钠的进一步吸附，从而抑制了方解石的浮选。      

剪切解络-超滤分离金属关键指标预测与验证

根据剪切解络-超滤过程中金属离子的动态浓度关系和质量守恒定律,采用CodeBlocks17.12软件编写程序,建立了剪切解络-超滤工艺关键指标预测模型,实现了金属离子浓度、回收率、体积稀释倍数等指标的预测,并用实验加以验证。依次在转速800 r/min、1 400 r/min、3 000 r/min下回收模拟废水中43 μg/L的Co²⁺、995 μg/L的Ni²⁺和88 μg/L的La³⁺,3种金属的回收率均达99.8%以上时,超滤过程体积稀释倍数的预测值分别为7.0、7.5、5.75,实验值分别为7.5、7.25、6.25,可见预测值与实验值基本一致。本模型对研究方案制定和调整有实际指导意义。     

Physicochemical and environmental characteristics of alkali leaching residue of wolframite and process for valuable metals recovery

Physicochemical and mineralogical characteristics of an alkali leaching residue of wolframite were studied by XRD, SEM?EDS, chemical phase analysis, mineral liberation analyzer (MLA), and TG?DSC methods. Batch leaching tests, toxicity characteristic leaching procedure (TCLP) tests and Chinese standard leaching tests (CSLT) were conducted to determine the environmental mobility of toxic elements. The results show that, due to the high contents of W, Fe, Mn, Sn, and Nb, the residue is with high resource value, but the content of a toxic element, As, is also high. The existing minerals of the investigated elements mainly occur as monomer particles, but it is difficult to extract these valuable metals by conventional acid leaching due to their mineral properties. The release of As increases over time in acidic environment. The leaching concentration of all investigated harmful elements through TCLP is within the limiting value, while the leaching concentration of As through CSLT exceeds the limiting value by more than 4 times, so the residue is classified as hazardous solid waste based on the Chinese standard. A process for valuable metals recovery from this residue was proposed. Preliminary experimental results indicated that the main valuable metals could be extracted effectively.